Code of Federal Regulations: Containing a Codification of Documents of General Applicability and Future Effect as of December 31, 1948, with Ancillaries and IndexDivision of the Federal Register, the National Archives, 2000 - Administrative law |
From inside the book
Results 1-5 of 35
Page 41
... mechanism is installed it shall be demonstrated that a weight equal to 2.2 times the weight of the empty blocks can be handily retrieved through the regular reeving of the falls at a rate of not less than 40 feet per minute at the drum ...
... mechanism is installed it shall be demonstrated that a weight equal to 2.2 times the weight of the empty blocks can be handily retrieved through the regular reeving of the falls at a rate of not less than 40 feet per minute at the drum ...
Page 54
... mechanism . Alternate arrange- ments which conform to the perform- ance requirements of this specification will be ... mechanism shall be simple to op- erate and provide ignition in most un- favorable weather . The mechanism shall be ...
... mechanism . Alternate arrange- ments which conform to the perform- ance requirements of this specification will be ... mechanism shall be simple to op- erate and provide ignition in most un- favorable weather . The mechanism shall be ...
Page 71
... mechanism shall be of material possessing excellent wearing ( ) Markomaankup . Signal pistols shall be of first class workmanship and shall be free from imperfections of maniac- ture affecting their serviceability or appearance . ( e ) ...
... mechanism shall be of material possessing excellent wearing ( ) Markomaankup . Signal pistols shall be of first class workmanship and shall be free from imperfections of maniac- ture affecting their serviceability or appearance . ( e ) ...
Page 78
... mechanism . ( 5 ) Gravity davits shall be tested for strength and operation at the place of manufacture in the presence of an in- spector . The davit arms , tracks , frames , attachments , etc. , shall be set up in a manner similar to ...
... mechanism . ( 5 ) Gravity davits shall be tested for strength and operation at the place of manufacture in the presence of an in- spector . The davit arms , tracks , frames , attachments , etc. , shall be set up in a manner similar to ...
Page 114
... mechanism . ( c ) Arrangements other than those specified by this subpart will be given special consideration . § 160.042-3 Construction . ( a ) The trackways of the skids shall be constructed of 6 " × 31⁄2 " x1⁄2 " structural angles ...
... mechanism . ( c ) Arrangements other than those specified by this subpart will be given special consideration . § 160.042-3 Construction . ( a ) The trackways of the skids shall be constructed of 6 " × 31⁄2 " x1⁄2 " structural angles ...
Other editions - View all
Common terms and phrases
accepted amended by CGD applicable approval tests ASTM boat body strap breaking strength buoy buoyant vests CGFR chapter Coast Guard approval color Commandant components conducted construction container davits device equipment facturer Federal Register fire float foam hybrid PFD ignite immersion suit inches Incorporation by reference independent laboratory inflatable liferaft inflation mechanism inspec inspections and tests inspector kapok ladder least less lifeboat lifejacket listing and labeling load lock stitch mandant manu manual manufac manufacturer manufacturer's marine marked meet the requirements ments monitor oil content percent performance Personal Flotation Devices PFD's pounds Procedure for approval production tests proval quired quirements ratus recognized laboratory rejected lot Reserved retroreflective rial sample seam Sept specimen Standard stitching submerged subpart suit surface tank temperature Test Method tested in accordance tests required thermocouple thickness tion Type U.S. Coast Guard Underwriters Laboratories valves vessel wearer weight workmanship
Popular passages
Page 400 - V National Highway Traffic Safety Administration, Department of Transportation (Parts 500—599) VI Federal Transit Administration, Department of Transportation (Parts 600—699) VII National Railroad Passenger Corporation (AMTRAK) (Parts 700—799...
Page 333 - ... of this section. (3) The standard time-temperature curve is defined by a smooth curve drawn through the following points: At the beginning of the test. 20 °C. (68 °F.) At the end of the first 5 minutes, 538 °C.
Page 4 - CFR part 51. To enforce any edition other than that specified in Paragraph (b) of this section, the Coast Guard must publish notice of change in the FEDERAL REGISTER; and the material must be available to the public.
Page 37 - A minimum factor of safety of six on the ultimate strength of the material shall be maintained at all times based on the approved working load. (b) Worm gears, spur gears, or a combination of both, may be used in the construction of lifeboat winches. All gears shall be machine cut and made of steel, bronze, or other suitable material properly keyed to shafts. The use of cast iron is not permitted for these parts. (c) Screws, nuts, bolts, pins, keys, etc., securing moving parts shall be fitted with...
Page 403 - Index List of Agency Prepared Indexes Parallel Tables of Statutory Authorities and Rules List of CFR Titles, Chapters, Subchapters, and Parts Alphabetical List of Agencies Appearing in the CFR Alphabetical List of Agencies Appearing in the CFR...
Page 396 - PROVISIONS RELATING TO PUBLIC CONTRACTS 50 Public Contracts, Department of Labor (Parts 50-1—50-999) 51 Committee for Purchase From People Who Are Blind or Severely Disabled (Parts 51-1—51-99) 60 Office of Federal Contract Compliance Programs, Equal Employment Opportunity, Department of Labor (Parts 60-1—60-999) 61 Office of the Assistant Secretary for Veterans...
Page 285 - DC, 20226. (b) Drawings and specifications. Manufacturers desiring approval of a new design or type of pressure-vacuum relief valve and spill valve shall submit drawings in quadruplicate showing the design of the valve, the sizes for which approval is requested, method of operation, thickness and material specifications of component parts, diameter of seat opening and lift of discs, mesh and size of wire of flame screens. (c) Pre-approval tests. Before approval is granted, the manufacturer shall...
Page 125 - Any examinations, inspections and tests which are required by the recognized laboratory for listed and labeled devices produced will be conducted by the laboratory inspector at the place of manufacture or other location at the option of the laboratory.
Page 388 - Office of Transportation, Department of Agriculture (Parts 3300—3399) XXXIV Cooperative State Research, .Education, and Extension Service. Department of Agriculture (Parts 3400—3499) XXXV Rural Housing Service, Department of Agriculture (Parts 3500— 3599...
Page 337 - ... as possible. The thermocouples shall be arranged so that the hot junction is approximately 10 cm. (4") from the nearest point of the specimen. (2) The furnace temperature shall be continuously controlled so as to follow the standard time-temperature curve within the accuracy specified in paragraph (c)(4) of this section. (3) The standard time-temperature curve is defined by a smooth curve drawn through the following points: At the beginning of the test, 20° C. (68° F.).