Standard Specifications for Construction of Roads and Bridges on Federal Highway Projects. FP-74 |
From inside the book
Results 1-5 of 64
Page 2
... faces of bridge parapet or railing . Calendar day . Any day shown on the calendar , beginning and ending at midnight . Change order . - A written order issued by the Engineer to the Con- tractor , covering changes within the scope of ...
... faces of bridge parapet or railing . Calendar day . Any day shown on the calendar , beginning and ending at midnight . Change order . - A written order issued by the Engineer to the Con- tractor , covering changes within the scope of ...
Page 4
... face from being adversely affected by subsequent blasting and excavation opera- tions . Profile grade . - The trace of a vertical plane intersecting the top surface of the proposed road construction , usually along the longitudi- nal ...
... face from being adversely affected by subsequent blasting and excavation opera- tions . Profile grade . - The trace of a vertical plane intersecting the top surface of the proposed road construction , usually along the longitudi- nal ...
Page 72
... faces of volume for pay quantities regardless of the excavation inside or out of these planes . 206.11 Foundation Fill . The volume of foundation fill to be for will be the number of cubic yards , measured in final position , of special ...
... faces of volume for pay quantities regardless of the excavation inside or out of these planes . 206.11 Foundation Fill . The volume of foundation fill to be for will be the number of cubic yards , measured in final position , of special ...
Page 76
... faces of retaining walls , wing walls , back faces of abutments , and over the extrados of arches , in accordance with these specifications and in reasonably close conformity with the requirements shown on the plans or as directed by ...
... faces of retaining walls , wing walls , back faces of abutments , and over the extrados of arches , in accordance with these specifications and in reasonably close conformity with the requirements shown on the plans or as directed by ...
Page 77
... faces or slopes steeper than the angle of repose of the material . When waterproofing is protected by roofing felt , a 4 - inch ( 102 mm ) layer of sand shall be placed between the coarse graded sheathing and the felt . Unless specific ...
... faces or slopes steeper than the angle of repose of the material . When waterproofing is protected by roofing felt , a 4 - inch ( 102 mm ) layer of sand shall be placed between the coarse graded sheathing and the felt . Unless specific ...
Contents
1 | |
6 | |
9 | |
10 | |
15 | |
17 | |
37 | |
45 | |
49 | |
61 | |
63 | |
73 | |
74 | |
77 | |
80 | |
81 | |
83 | |
85 | |
93 | |
103 | |
155 | |
179 | |
267 | |
302 | |
303 | |
304 | |
305 | |
306 | |
307 | |
308 | |
309 | |
310 | |
339 | |
340 | |
343 | |
345 | |
346 | |
350 | |
361 | |
363 | |
365 | |
374 | |
381 | |
385 | |
387 | |
391 | |
397 | |
401 | |
402 | |
406 | |
411 | |
412 | |
413 | |
414 | |
425 | |
457 | |
Common terms and phrases
accordance with subsection adjusted aluminum applied approved areas ASTM backfill Basis of Payment batch bid schedule bituminous material bituminous surface treatment bolts cleaned coat compacted complete in place compressive strength Construction Requirements contract price contract unit price Contractor crete Cubic yard curb curing designated device diameter Emulsified asphalt Engineer equipment excavation expansion joints falsework feet finishing forms furnished Gallon grade grout holes inch joints layer length less Linear foot load masonry ment metal Method of Measurement minimum mixer mixing mortar operations paid paint pavement pay factor Pay item Pay unit percent permitted pipe plans plant plates portland cement precast Precast concrete prestressed concrete price and payment railing reasonably close conformity reinforcing steel removed requirements of AASHTO requirements of subsection rivets samples seal Section shown special provisions specific gravity specified square yard stockpiled stone Structural steel subgrade surface temperature thickness timber tion unless otherwise weight welds width
Popular passages
Page 437 - The Contractor warrants that no person or selling agency has been employed or retained to solicit or secure this contract upon an agreement or understanding for a commission, percentage, brokerage, or contingent fee...
Page 432 - Except as otherwise provided in this contract, any dispute concerning a question of fact arising under this contract which is not disposed of by agreement shall be decided by the Contracting Officer, who shall reduce his decision to writing and mail or otherwise furnish a copy thereof to the Contractor.
Page 432 - ... representative or board is alleged: Provided, however, That any such decision shall be final and conclusive unless the same is fraudulent or capricious or arbitrary or so grossly erroneous as necessarily to imply bad faith, or is not supported by substantial evidence.
Page 440 - UTILIZATION OF SMALL BUSINESS CONCERNS (a) It is the policy of the Government as declared by the Congress that a fair proportion of the purchases and contracts for supplies and services for the Government be placed with small business concerns.
Page 440 - September 24, 1965, so that such provisions will be binding upon each subcontractor or vendor. The contractor will take such action with respect to any subcontract or purchase order as the contracting agency may direct as a means of enforcing such provisions including sanctions for noncompliance; Provided, however, That in the event the contractor becomes involved in or is threatened with, litigation with a subcontractor or vendor as a result of such direction by the contracting agency, the contractor...
Page 439 - (5) The contractor will furnish all information and reports required by Executive Order No. 11246 of September 24, 1965, and by the rules, regulations, and orders of the Secretary of Labor, or pursuant thereto, and will permit access to his books, records, and accounts by the contracting agency and the Secretary of Labor for purposes of investigation to ascertain compliance with such rules, regulations, and orders.
Page 443 - Contractor in the event of failure of the Contractor and the Contracting Officer to agree upon the whole amount to be paid to the Contractor by reason of the termination of work pursuant to this clause...
Page 448 - ENTERPRISES (a) It is the policy of the Government that minority business enterprises shall have the maximum practicable opportunity to participate in the performance of Government contracts.
Page 453 - The provisions of paragraphs (b), (c), (d), and (e) of this clause do not apply to openings which the contractor proposes to fill from within his own organization or to fill pursuant to a customary and traditional employer-union hiring arrangement. This exclusion does not apply to a particular opening once an employer decides to consider applicants outside of his own organization or employer-union arrangement for that opening. (h) As used in this clause: (1) "All suitable employment openings...
Page 30 - The delay in the completion of the work arises from unforeseeable causes beyond the control and without the fault or negligence of the Contractor...