Technical Manual |
From inside the book
Results 1-5 of 6
Page 2
... STOP Mall KNOB E THROTTLE CARRYING BRACKET TURNTABLE BASE VISE TRACK TOOTH LOCATOR TILT TABLE LEVER A TOOTH LOCATOR LOCKING SCREW TURN TABLE BOLT B HOOK ANGLE INDICATOR C 11 2 WING NUT FOR ADJUSTING TENSION IN TABLE LIFT SPRING FIGURE 2 ...
... STOP Mall KNOB E THROTTLE CARRYING BRACKET TURNTABLE BASE VISE TRACK TOOTH LOCATOR TILT TABLE LEVER A TOOTH LOCATOR LOCKING SCREW TURN TABLE BOLT B HOOK ANGLE INDICATOR C 11 2 WING NUT FOR ADJUSTING TENSION IN TABLE LIFT SPRING FIGURE 2 ...
Page 3
... stop in position shown in Fig . 4 , when adjusting and removing chains . When ready to grind , flip the safety stop ... TOOTH LOCATOR TOOTH LOCATOR LOCKING SCREW WING NUT FOR LOCKING TILT TABLE ( ADJUSTING HOOK ANGLE ] FIGURE 4 ...
... stop in position shown in Fig . 4 , when adjusting and removing chains . When ready to grind , flip the safety stop ... TOOTH LOCATOR TOOTH LOCATOR LOCKING SCREW WING NUT FOR LOCKING TILT TABLE ( ADJUSTING HOOK ANGLE ] FIGURE 4 ...
Page 5
... teeth ) , remove enough metal so that they are about 1/32 inch lower than side cutters . Care should be ex- ercised to make all of each kind of teeth the same height . 225714 0-52-2 5 TOOTH STOP H FIGURE 9 Remove the chain saw sharpener.
... teeth ) , remove enough metal so that they are about 1/32 inch lower than side cutters . Care should be ex- ercised to make all of each kind of teeth the same height . 225714 0-52-2 5 TOOTH STOP H FIGURE 9 Remove the chain saw sharpener.
Page 6
... stopped , adjust knob E until the face angle of the unground tooth fits the contour or outline of the grinding wheel . The depth that the wheel goes into the saw is adjusted by screw F. Set tooth stop H as shown in Fig . 9 , locating on the ...
... stopped , adjust knob E until the face angle of the unground tooth fits the contour or outline of the grinding wheel . The depth that the wheel goes into the saw is adjusted by screw F. Set tooth stop H as shown in Fig . 9 , locating on the ...
Page 12
... stop stud I No. 105083 3/16 " x8 " Groove pin type I 2 No. 105102 4x2 Groove pin I No. 102048 3/8 " -16x2 " H.H. cap ... Tooth locator assembly , consisting of : 12.
... stop stud I No. 105083 3/16 " x8 " Groove pin type I 2 No. 105102 4x2 Groove pin I No. 102048 3/8 " -16x2 " H.H. cap ... Tooth locator assembly , consisting of : 12.
Other editions - View all
Common terms and phrases
air cleaner elbow Ball bearing buretor cap screw Carburetor throttle Center compression CHAIN SAW SHARPENERS CHANGE OIL check valve Choke lever choke valve CIRCULAR SAW SHARPENERS clogged Control lever copy to T/O Crankshaft CUT SCREW F Cylinder mounting washer DEPTH OF CUT Dust cover engine fails engine operation Flywheel fuel system Gas filter gas line gas pipe gas tank gasket GASOLINE ENGINE grinding wheel Groove pin type gummy heavier than S.A.E. Ignition knob legs LOCATOR LOCKING SCREW locknut Lockwasher shakeproof loosening lubrication machine Magneto plate MALL CHAIN motor Muffler Needle valve packing oil reservoir Piston pulley Remove SAFETY STOP SAW SHARPENERS TRIPOD-MOUNTED SERVICING REFERENCE CHART set screw shown in Fig SHUT-OFF Spacer Spark plug Speed adjuster spindle starter pulley stop H tension TOOTH LOCATOR LOCKING tooth stop Top compression Turntable base type of tooth Upper carburetor body Valve cover Vise jaw VISE TRACK WAR DEPARTMENT Wing nut